The high profile Vickers Elite Battlesight rear has a .145” wide, deep U-Notch for optimum sighting in low-light, dynamic range conditions and is a perfect match to our .125” wide front sights. The concave non-reflective rear blade is serrated 40 lines per inch, while the notch area is recessed into a semi-circular pocket for a crisp, protected sight picture. Two hardened set-screws ensure this sight will never shoot loose under the most demanding conditions. This snag-free rear sight also has a shelf shape that enables one-hand slide cycling or malfunction clearance and a rugged, non-reflective matte black parkerized finish. The Vickers Elite Battlesight is available with single dot Tritium and plain black serrated rear blades and your choice of black serrated, green/red fiber optic, tritium and genuine, never dulling gold bead front sight styles. The high profile of the Vickers Elite Battlesight allows the use of a taller front sight and deeper rear notch for better sight tracking during high speed shooting situations. Once you try this sight system you will be convinced that the Vickers Elite Battlesight is the best performance upgrade you can make to your Glock® pistol! Larry Vickers is a retired US Army 1st SFOD- Delta combat veteran with years of experience in the firearms industry as a combat marksmanship instructor and industry consultant. Find out more about Larry Vickers on his website www.vickerstactical.com NOTE: Sights may require minor fitting and may not be returned after installation. The Vickers Elite Glock® Sight set requires the use of a .245”tall front sight for all caliber Glock® pistols except for .45 ACP and 10mm which will typically require the .230” front sight. Sights may require minor fitting and may not be returned after installation. These front sights are taller than factory Glock® and not compatible with standard factory rear sights without adjusting the sight height. Wilson Combat Vickers Glock® rear sights are not compatible with factory Glock® MOS (Modular Optic System) slide models due to the rearward relocation of the sight dovetail position. Glock Rear Sight Installation FAQ Remove the magazine and make sure your pistol is unloaded. Remove and Field strip slide assembly and secure the slide in a padded vise. Remove existing rear sight with hammer and punch. Clean rear sight dovetail and press in new rear sight from right to left. If rear sight will not start into approximately 50% of the dovetail you may need to remove very small amounts of material from the bottom and sides of the dovetail portion of the rear sight-usually just a few light passes will do. A safe sided dovetail file, small diamond hone or sanding stick are good tools for this. Go slowly and check your fit. Once you are able to get 50% of the sight base into the dovetail attempt to tap the sight in place with a hammer and non marring punch/dowel (wood, polymer, aluminum) or appropriate sight pusher. If using a steel or brass punch protect the sight/punch with several layers of duct tape. Fine adjust your windage with a rear sight armorers tool or non marring punch. After you fine adjust rear sight windage install dual locking screws with a threadlocking compound like Loctite on the threads. Note-if the rear sight is loose in the dovetail your dovetail is cut oversize and the new rear sight may require peening on the edges of the dovetail for a proper fit.

Snag Free Front Sight, Red Fiber Optic, Vickers Elite for Glock® .245” .245” height .125" wide Red Fiber optic (.0585" Diameter) Glock® Vickers Elite replacement front sight for 9mm, .40, 357 and .45 GAP calibers Black Parkerized finish Note: .The Vickers Elite Glock® Sight set requires the use of a .245” tall front sight for all caliber Glock® pistols except for .45 ACP and 10mm which will typically require the .230” front sight. Sights may require minor fitting and may not be returned after installation. These front sights are taller than factory Glock® and not compatible with standard factory rear sights without adjusting the sight height. Replacement fiber optic rods found here: http://shopwilsoncombat.com/Fiber-Optic-Rod-Replacement-Red-0585-x-1/productinfo/583G/ Glock Front Sight Installation FAQ Remove the magazine and make sure your pistol is unloaded. Remove and field strip slide assembly. Remove Glock factory front sight with a punch or pliers. Gen-4 Glock pistols will require a front sight tool to remove the front sight retaining screw. After removal of front sight clean and degrease sight hole in slide and check the fit of the new front sight. If the new sight will seat at least 50% tap it in place with a non marring punch taking care that it remains straight. If the sight will not seat you may have to sand or lightly file the circumference of the front sight base. Install with aftermarket Glock front sight tool or 3/16” socket that has been modified to clear the slide. For a more permanent installation use red loctite around the circumference of the sight base. Reassemble your pistol and make sure sight retaining screw is not impeding operation.