Menu

All Products

View as Grid List
Sort by

USED KAC SR25 20" ECR CUSTOM

$9,000.00 $4,550.00
The KAC 20” Enhanced Combat Rifle is based upon improvements for a 20” Duty System. This system features a 5R Rifled Match barrel with a 762QDC flash hider that effectively eliminates muzzles flash and allows the family of 762QDC suppressors to be easily added. The ECR also boasts an enlarged Ejection Port and Carbon Cuter bolt carrier which allow for improved reliability when firing suppressed or in less than ideal environments.

EraThr3 Primo Special

$3,595.00 $2,790.00
EraThr3 Primo Special E3 Accuracy Guarantee: Whether you are shooting steel, providing for the family, or hunting bad guys, we are here to support your efforts, and provide you the competitive edge required to prevail with a "Match Grade Rifle”. To achieve the expected level of accuracy, every unit is hand-crafted with extreme attention to detail in its fit, form, and function. Building an E3 rifle starts with a match grade barrel, chamber… and so on. We can guarantee the quality of our products and stand behind trusted suppliers to do the same, however we cannot guarantee the skill level of every shooter, quality of sub-par ammunition, and/or choice of optics & aftermarket accessories. Every rifle is tried, tested, and proven with Prime ammunition prior to delivery. This doesn't mean that our rifles won’t run with various types of ammunition, including custom loads or hunting grade products, it's just simply no guarantee that they will. Rifles, just like your favorite pair of pants, have a lifespan. Even with easy use, and great care, things break, wear-out, etc. We stand behind our goods, and will support them to the end. However, we also expect that you understand the definition of “normal wear and tear”. We highly recommend the training component to all of our customers, and follow the same advice ourselves. Being good at one’s craft takes good equipment, hard work, and dedication.

EraThr3 16" Carbon Supreme

$3,250.00 $2,632.50
We're proud to offer the most refined rifles on the planet. And after months of R&D, we've developed multiple configurations that cover a broad range of requirements, yet focus on one thing... Absolute dominance in the marketplace. EraThr3 gas guns are assembled with a free-float handguard, single-point cut 416R PROOF Research barrel, and a hand-selected group of top top-notch component parts. Meticulously built on our own billet receivers, each assembly is hand finished and proven on the range prior to delivery. su·preme /so͞oˈprēm/ adjective 1. (of authority or an office, or someone holding it) superior to all others. With blatant disregard to the masses, we set-out to design and build what "we" wanted in a modern-day AR-15. Rather than listen to some metrics pushing sales team, or rely on their boring market research data, we opted to do this one our way. And what we've found, is that those pencil pushers aren't always right. We're passionate about what we do, and what we do is win. Most every rifle out there is gonna go "bang", we get that part. This one just happens to do it with a new sense of style and greatness, one that you can have as well.

EraThr3 Nashville Rifle

$3,150.00 $2,605.50
We're proud to offer the most refined rifles on the planet. And after months of R&D, we've developed multiple configurations that cover a broad range of requirements, yet focus on one thing... Absolute dominance in the marketplace. EraThr3 gas guns are assembled with a free-float handguard, single-point cut 416R PROOF Research barrel, and a hand-selected group of top top-notch component parts. Meticulously built on our own billet receivers, each assembly is hand finished and proven on the range prior to delivery.

EraThr3 16" Stainless Rifle Custom Gray/Orange Distressed

$2,565.00
We're proud to offer the most refined rifles on the planet. And after months of R&D, we've developed multiple configurations that cover a broad range of requirements, yet focus on one thing... Absolute dominance in the marketplace. EraThr3 gas guns are assembled with a free-float handguard, single-point cut 416R PROOF Research barrel, and a hand-selected group of top top-notch component parts. Meticulously built on our own billet receivers, each assembly is hand finished and proven on the range prior to delivery.

EraThr3 Cali Special 5.56mm Rifle

$3,250.00 $2,475.00
E3 Accuracy Guarantee: Whether you are shooting steel, providing for the family, or hunting bad guys, we are here to support your efforts, and provide you the competitive edge required to prevail with a "Match Grade Rifle”. To achieve the expected level of accuracy, every unit is hand-crafted with extreme attention to detail in its fit, form, and function. Building an E3 rifle starts with a match grade barrel, chamber… and so on. We can guarantee the quality of our products and stand behind trusted suppliers to do the same, however we cannot guarantee the skill level of every shooter, quality of sub-par ammunition, and/or choice of optics & aftermarket accessories. Every rifle is tried, tested, and proven with "Black Hills Match" ammunition prior to delivery. This doesn't mean that our rifles won’t run with various types of ammunition, including custom loads or hunting grade products, it's just simply no guarantee that they will. Rifles, just like your favorite pair of pants, have a lifespan. Even with easy use, and great care, things break, wear-out, etc. We stand behind our goods, and will support them to the end. However, we also expect that you understand the definition of “normal wear and tear”. We highly recommend the training component to all of our customers, and follow the same advice ourselves. Being good at one’s craft takes good equipment, hard work, and dedication.

Agency Arms 34 G3 Urban T-800 BW 2-Tone

$2,599.00 $2,339.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 BONESAW SS Barrel

$2,550.00 $2,295.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 BONESAW TiN Barrel

$2,550.00 $2,295.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 BONESAW TiN Barrel

$2,450.00 $2,205.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 Urban DLC SS Barrel

$2,399.00 $2,159.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Bonesaw Armor Stipple DLC

$2,399.00 $2,159.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

War Sport GPR CC BLACK

$2,395.00 $1,575.00
WAR SPORT GPR-CC: BASIC SPECS: CAL: .223 REM, WYLDE CHAMBER, 1:8 RH, QPQ MELONITE BARREL LENGTH: 16.0" (WITH GP-S COMP), OAL: 16.2" MID LENGTH DI GAS SYSTEM (Gas Tube & Low Pro Gas Block, QPQ MELONITE) WEIGHT (W/ 30-RD MAG): 7.5-LBS WEIGHT CARBINE: 6.5-LBS LENGTH OPEN: 35.5" LENGTH CLOSED: 32.75"

Agency Arms 20 G4 Urban BW Bronze

$2,387.00 $2,148.30

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 Urban SS Match

$2,385.00 $2,146.50

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 FDE 2-Tone

$2,349.00 $2,114.10
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

Agency Arms Glock 34 Gen 3 DLC

$2,339.00 $2,105.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 19 Gen 4 URBAN TUNGSTEN

$2,330.00 $2,097.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Dark Earth Bonesaw DTF 2-Tone

$2,329.00 $2,096.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Bonesaw 2-Tone

$2,329.00 $2,096.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Grey Bonesaw 2-Tone Stipple

$2,329.00 $2,096.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 G4 Hybrid Tungsten

$2,312.00 $2,080.80
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 G4 Urban

$2,287.00 $2,058.30

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 G4 Urban

$2,287.00 $2,058.30

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 OD Urban 2-Tone

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 34 G4 Urban DLC

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 OD Bonesaw

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 34 Gen 3 DLC

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 34 G3 OD Urban DLC

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 OD Bonesaw 2-Tone

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Green Frame Bonesaw DLC JARVIS Cut

$2,274.00 $2,046.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Hybrid Multicam

$2,259.00 $2,033.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Urban Multicam

$2,259.00 $2,033.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Urban Multicam

$2,259.00 $2,033.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 OD Hybrid Multicam

$2,259.00 $2,033.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 OD Hybrid Armor Stipple

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Urban BW Burnt Bronze

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Urban Midnight Bronze

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 GREY Frame DLC

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 19 Gen 4 Green Frame BW Graphite

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 19 Gen 4 Green Frame BW Bronze

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 17 GEN 4 Hybrid TiN

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 GREY Frame DLC

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 OD Urban Armor Stipple DLC

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 19 Gen 4 URBAN T-800

$2,230.00 $2,007.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 OD Urban 2-Tone

$2,229.00 $2,006.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 BW Burnt Bronze

$2,219.00 $1,997.10
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

Agency Arms 26 G 4 Tungsten

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G 4 Tungsten

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 OD Bonesaw DLC

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 OD Bonesaw DLC

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 Green Frame Bonesaw DLC

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Urban Burnt Bronze

$2,174.00 $1,956.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19C G4 Urban Comp DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 OD Bonesaw DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 17 GEN 4 URBAN BLACK

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 17 GEN 4 URBAN BLACK

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Dark Earth Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Dark Earth Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Dark Earth Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 Gen 4 Grey Frame DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Green Frame Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 OD Hybrid DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17C Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17C Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 OD Bonesaw DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19C G4 Urban Comp DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 OD Bonesaw DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 Concrete Grey

$2,144.00 $1,929.60

Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group.

 

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 Crushed Silver

$2,144.00 $1,929.60

Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group.

 

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 Urban Blue Titanium

$2,124.00 $1,911.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 Urban Blue Titanium

$2,124.00 $1,911.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 Graphite Black

$2,119.00 $1,907.10

Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group.

 

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 DLC

$2,119.00 $1,907.10
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

Agency Arms 26 G3 OD Hybrid Multicam

$2,109.00 $1,898.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Fowler G19 Gen3 MARK 2 TUNG BLK Match Barrel

$2,450.00 $1,890.00
Our Complete Package is the ultimate choice for shooting enthusiasts who want the most out of their firearms. The complete package includes the base firearm along with all the alterations that make the Mark 2 the premier enhanced Glock platform. Treatment includes full grip work, slide cuts and coating, polishing of internal parts, sight install, and optional match barrel fitment.

Fowler G19 Gen3 MARK 2 TUNG SS Match Barrel

$2,450.00 $1,890.00
Our Complete Package is the ultimate choice for shooting enthusiasts who want the most out of their firearms. The complete package includes the base firearm along with all the alterations that make the Mark 2 the premier enhanced Glock platform. Treatment includes full grip work, slide cuts and coating, polishing of internal parts, sight install, and optional match barrel fitment.

AGENCY ARMS GLOCK 17L GEN 3 Urban DLC

$2,099.00 $1,889.10
Gun Specific Options: -9mm Generation 3 -Urban -DLC Coating -Magwell -Agency Backplate -(2) 17rnd Magazines

Agency Arms 17 Gen 3 Urban DLC

$2,099.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 DLC

$20,990.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 DLC

$20,990.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 DLC

$20,990.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 DLC

$20,990.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 Urban DLC

$2,099.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 Urban DLC

$2,099.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 Urban DLC

$2,099.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 Urban Burnt Bronze

$2,024.00 $1,821.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 43 OD Hybrid 2-Tone

$2,010.00 $1,809.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G3 DLC

$1,999.00 $1,799.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G3 OD Hybrid DLC

$1,999.00 $1,799.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms TWC 19 PATROL SS Barrel

$1,900.00 $1,710.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 43 Hybrid DLC

$1,880.00 $1,692.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 43 Hybrid DLC

$1,880.00 $1,692.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 43 Hybrid DLC

$1,880.00 $1,692.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Wilson Combat Standard Shotgun GRAY

$1,540.00 $1,309.00
The Standard Model incorporates the features many of our owners want most in their defensive shotguns, in a value-packed package.

MAXFLO 3D AFD SUPPRESSOR 5.56 MM

$1,495.00 $1,345.00
NEXGEN2 Defense (NG2) has brought new suppression technology to the market with their MAXFLO 3D™. Utilizing “Advanced Flow Dynamics™ (AFD)” Zero Back-Pressure Suppression™ technology. The MAXFLO 3D rewrites the rules in firearms suppression. Rather than start with existing designs, NG2 erased the template and started from scratch. The result changes the game in firearms suppression. The MAXFLO 3D™ virtually eliminates all of the major issues common with firearms suppressors, back-pressure, first round “pop” and flash, accuracy robbing turbulence, recoil, excessive heat buildup, and more. All while maintaining hearing-safe levels of sound suppression across a wide variety of weapons systems and calibers. Quiet, soft-shooting, light-weight, strong, and user-serviceable, the MAXFLO 3D™ has it all.

MAXFLO 3D AFD SUPPRESSOR 7.62 MM

$1,495.00 $1,345.00
NEXGEN2 Defense (NG2) has brought new suppression technology to the market with their MAXFLO 3D™. Utilizing “Advanced Flow Dynamics™ (AFD)” Zero Back-Pressure Suppression™ technology. The MAXFLO 3D rewrites the rules in firearms suppression. Rather than start with existing designs, NG2 erased the template and started from scratch. The result changes the game in firearms suppression. The MAXFLO 3D™ virtually eliminates all of the major issues common with firearms suppressors, back-pressure, first round “pop” and flash, accuracy robbing turbulence, recoil, excessive heat buildup, and more. All while maintaining hearing-safe levels of sound suppression across a wide variety of weapons systems and calibers. Quiet, soft-shooting, light-weight, strong, and user-serviceable, the MAXFLO 3D™ has it all.

Agency Arms URBAN DTF TOPEND

$1,175.00 $1,057.50

Agency Arms FIELD DTF TOPEND

$1,175.00 $1,057.50

Wilson Combat Border Patrol Shotgun GRAY

$1,135.00 $964.75
The Border Patrol Model has an outstanding, well-earned reputation as the workhorse of Wilson Combat® / ScattergunTechnologies™ shotguns.

Deadair Silencers Wolverine PBS-1

$895.50
PEOPLE SAID IT COULDN’T BE DONE. You want to build a dedicated AK suppressor? “You can’t do that.” “They’re too loud.” “What about non-concentric threads?” “How will it mount consistently?” “There’s too many variations.” And yet, here it is. AK and combloc gun lovers rejoice. The Wolverine strikes the perfect balance between suppression and minimal back pressure. SO WHAT DOES THE WOLVERINE PBS-1 SILENCER FIT? You won’t have to buy multiple silencers to fit different threaded combloc rifles. The Wolverine offers user changeable thread inserts. The Wolverine ships with a 14L thread insert. We plan on making 14R, 24R, 26L, 15mm, 16mm, 1/2×28, 5/8×24, and 9/16L as well; and possibly more will be added to the list depending on demand.

Hoback Agent Knife, Agency Arms Limited Edition Collaboration Woodland MULTICAM

$850.00
The Limited Edition "Agent Knife" combines the Jake Hoback Kwaiback design with the Agency Arms logo and markings to complement the distinct geometry of the Agency Arms Glock slide.

Trijicon RMR Sight Adjustable (LED) - 3.25 MOA Red Dot RM06 TYPE 2

$629.10
Developed to improve precision and accuracy with any style or caliber of weapon, the Trijicon RMR (Ruggedized Miniature Reflex) is designed to be as durable as the legendary ACOG. The RM06 is an LED sight powered by a standard CR2032 battery. Housed in rugged forged aluminum, the RMR is extremely tough yet lightweight. New easy-to-use adjusters with audible clicks allow for quick windage and elevation adjustments. With eight available brightness settings, the reticle can be manually adjusted by pressing the plus or minus buttons on either side of the unit. To switch to auto adjust mode simply press both buttons simultaneously and release. To save battery life, turn the optic off by pressing both buttons simultaneously and holding for 3 seconds. The Trijicon RMR is tougher than any alternative and suitable for military, law enforcement and hunting applications.

OEM GLOCK 19 GEN 5

$699.00 $595.00

Half Face Blades - Disaster Breacher W/ Bocote Handle

$445.50
Half Face Blades was founded by Andrew Arrabito, Navy SEAL (ret.), to meet the need for high-quality, “go to” knives and axes – usable, personalized, functional, versatile tools that work for every person in every walk of life. Andrew grew up hunting, camping and fishing in the great outdoors. After high school he joined the US Navy, determined to achieve the honor of serving in the United States Navy SEAL Teams. It was during his time in the Teams that Andrew decided to bring the “end user” back to the beginning, to learn blade-smithing. From the beginning, Andrew’s goal was to make simple blade designs for consumers who demand the finest products. With his real-world experience in using cutting devices in super-charged action, Andrew understands what will be demanded from his blades. And he makes them to meet those demands. Half Face Blades knives are designed with the distinction and ruggedness required for the work they are intended to do. Each knife is calculated to meet requirements gained by experience, by testing knives and axes, by using them over time at sea and in remote wildernesses. HFB knives bring the soul of rugged, dependable, combat knives and tools to a variety of settings - from special operations tools for warriors, hunters and backpackers, to knives for the kitchen and great American workers. “I wanted each person to have a usable tool, embodied with a warrior’s spirit, that will perform to their needs during their walk in life.”

Half Face Blades - Disaster Breacher W/ Blood Wood Handle

$445.50
Half Face Blades was founded by Andrew Arrabito, Navy SEAL (ret.), to meet the need for high-quality, “go to” knives and axes – usable, personalized, functional, versatile tools that work for every person in every walk of life. Andrew grew up hunting, camping and fishing in the great outdoors. After high school he joined the US Navy, determined to achieve the honor of serving in the United States Navy SEAL Teams. It was during his time in the Teams that Andrew decided to bring the “end user” back to the beginning, to learn blade-smithing. From the beginning, Andrew’s goal was to make simple blade designs for consumers who demand the finest products. With his real-world experience in using cutting devices in super-charged action, Andrew understands what will be demanded from his blades. And he makes them to meet those demands. Half Face Blades knives are designed with the distinction and ruggedness required for the work they are intended to do. Each knife is calculated to meet requirements gained by experience, by testing knives and axes, by using them over time at sea and in remote wildernesses. HFB knives bring the soul of rugged, dependable, combat knives and tools to a variety of settings - from special operations tools for warriors, hunters and backpackers, to knives for the kitchen and great American workers. “I wanted each person to have a usable tool, embodied with a warrior’s spirit, that will perform to their needs during their walk in life.”

Hoback OSF Authorized Dealer Exclusive Knife, 3.5" Blade

$495.00
"Authorized Dealer Exclusive OSF" This knife will be available only through our Authorized Dealers. Please click the "Notify Me" button to receive notification when our dealers receive them. The OSF3.5 has been one of those knives that has always had a huge following. OSF stands for "Open Source Folder." As Jake says, "When I started this project in 2010, it was after I had spent countless hours researching folding knives, mechanisms and lock geometry. I thought to myself, why not put this information into a solid model so that everyone who is getting into making folders can start with a finished idea to look at while they build their very own awesome knife. So I set out to make the knife in such a way that it could be made with simple tools, no CNC necessary. All you would need to do is waterjet cut a blank and start drilling and tapping." The knife design itself is a modified sheep’s foot blade with a properly engineered frame set. The single point rear standoff/backspacer is large enough to handle knife stresses but small enough to allow a rather large handle to blade ratio. The blade steel is CPM-S35VN, with an excellent heat treat that seamlessly flows into and out of the titanium frame set. There are several options to choose from to make this knife your very own -- including pocket clips, pivots, backspacers, and inlays. This all adds up to a NPD (Never Put it Down), not just an EDC!

AGENCY ARMS PREMIER LINE GLOCK 17 BARREL

$270.00
Agency Arms Premier Lines Are for those who demand uncompromised performance and unrivaled appearance. While each of our lines maintain the same core accuracy and reliability, the Premier Line’s focus is giving attention to every detail. With added performance from our polished feed ramp to a polished crown to reduce friction. (see Specifications for more info)

AGENCY ARMS PREMIER LINE GLOCK 19 BARREL

$270.00
Agency Arms Premier Lines Are for those who demand uncompromised performance and unrivaled appearance. While each of our lines maintain the same core accuracy and reliability, the Premier Line’s focus is giving attention to every detail. With added performance from our polished feed ramp to a polished crown to reduce friction. (see Specifications for more info)

AGENCY ARMS PREMIER LINE GLOCK 34 BARREL

$270.00
Agency Arms Premier Lines Are for those who demand uncompromised performance and unrivaled appearance. While each of our lines maintain the same core accuracy and reliability, the Premier Line’s focus is giving attention to every detail. With added performance from our polished feed ramp to a polished crown to reduce friction. (see Specifications for more info)

Blacklist Ultra Match G43 Barrel THREADED

$193.49
Blacklist Industries Ultra Match barrels are some of the most precise match grade barrels in the industry. Precision Machined from certified 416R stainless steel bar stock for superior strength and durability. Critical manufacturing tolerances, multiple quality-control checks, and an advanced broach rifling process allows us to guarantee the exact same accuracy from each and every barrel while also achieving greater accuracy over a stock barrel. Eight column flutes are added at safe depths which provide a custom look and finish to the barrels. Our barrels also feature a recess crown at the muzzle. The recess crown preserves the barrels accuracy by preventing the very edge of the rifling from being exposed or damaged in any way that can affect the dynamics of the bullet. Our fully supported match chamber is compatible with all bullet materials and reduces the risk of dangerous pressure spikes that are common in most stock barrels.

Blacklist Ultra Match G26 Barrel THREADED

$193.49
Blacklist Industries Ultra Match barrels are some of the most precise match grade barrels in the industry. Precision Machined from certified 416R stainless steel bar stock for superior strength and durability. Critical manufacturing tolerances, multiple quality-control checks, and an advanced broach rifling process allows us to guarantee the exact same accuracy from each and every barrel while also achieving greater accuracy over a stock barrel. Eight column flutes are added at safe depths which provide a custom look and finish to the barrels. Our barrels also feature a recess crown at the muzzle. The recess crown preserves the barrels accuracy by preventing the very edge of the rifling from being exposed or damaged in any way that can affect the dynamics of the bullet. Our fully supported match chamber is compatible with all bullet materials and reduces the risk of dangerous pressure spikes that are common in most stock barrels.

Blacklist Ultra Match G17 Barrel THREADED

$193.49
Blacklist Industries Ultra Match barrels are some of the most precise match grade barrels in the industry. Precision Machined from certified 416R stainless steel bar stock for superior strength and durability. Critical manufacturing tolerances, multiple quality-control checks, and an advanced broach rifling process allows us to guarantee the exact same accuracy from each and every barrel while also achieving greater accuracy over a stock barrel. Eight column flutes are added at safe depths which provide a custom look and finish to the barrels. Our barrels also feature a recess crown at the muzzle. The recess crown preserves the barrels accuracy by preventing the very edge of the rifling from being exposed or damaged in any way that can affect the dynamics of the bullet. Our fully supported match chamber is compatible with all bullet materials and reduces the risk of dangerous pressure spikes that are common in most stock barrels.

Blacklist Ultra Match G19 Barrel THREADED

$193.49
Blacklist Industries Ultra Match barrels are some of the most precise match grade barrels in the industry. Precision Machined from certified 416R stainless steel bar stock for superior strength and durability. Critical manufacturing tolerances, multiple quality-control checks, and an advanced broach rifling process allows us to guarantee the exact same accuracy from each and every barrel while also achieving greater accuracy over a stock barrel. Eight column flutes are added at safe depths which provide a custom look and finish to the barrels. Our barrels also feature a recess crown at the muzzle. The recess crown preserves the barrels accuracy by preventing the very edge of the rifling from being exposed or damaged in any way that can affect the dynamics of the bullet. Our fully supported match chamber is compatible with all bullet materials and reduces the risk of dangerous pressure spikes that are common in most stock barrels.

Blacklist Ultra Match G17 Barrel NON-THREADED

$184.49
Blacklist Industries Ultra Match barrels are some of the most precise match grade barrels in the industry. Precision Machined from certified 416R stainless steel bar stock for superior strength and durability. Critical manufacturing tolerances, multiple quality-control checks, and an advanced broach rifling process allows us to guarantee the exact same accuracy from each and every barrel while also achieving greater accuracy over a stock barrel. Eight column flutes are added at safe depths which provide a custom look and finish to the barrels. Our barrels also feature a recess crown at the muzzle. The recess crown preserves the barrels accuracy by preventing the very edge of the rifling from being exposed or damaged in any way that can affect the dynamics of the bullet. Our fully supported match chamber is compatible with all bullet materials and reduces the risk of dangerous pressure spikes that are common in most stock barrels.

Blacklist Ultra Match G26 Barrel NON-THREADED

$184.49
Blacklist Industries Ultra Match barrels are some of the most precise match grade barrels in the industry. Precision Machined from certified 416R stainless steel bar stock for superior strength and durability. Critical manufacturing tolerances, multiple quality-control checks, and an advanced broach rifling process allows us to guarantee the exact same accuracy from each and every barrel while also achieving greater accuracy over a stock barrel. Eight column flutes are added at safe depths which provide a custom look and finish to the barrels. Our barrels also feature a recess crown at the muzzle. The recess crown preserves the barrels accuracy by preventing the very edge of the rifling from being exposed or damaged in any way that can affect the dynamics of the bullet. Our fully supported match chamber is compatible with all bullet materials and reduces the risk of dangerous pressure spikes that are common in most stock barrels.

AGENCY ARMS MID LINE GLOCK 19 BARREL

$180.00
Agency Arms Mid Line are for those who desire functionality as well as a unique appearance. While each of our lines maintain the same core accuracy and reliability, Our Mid Line focuses on additional machining enhancements and appearance while only a having modest price increase over the Standard Line models.

AGENCY ARMS MID LINE GLOCK 17 BARREL

$180.00
Agency Arms Mid Line are for those who desire functionality as well as a unique appearance. While each of our lines maintain the same core accuracy and reliability, Our Mid Line focuses on additional machining enhancements and appearance while only a having modest price increase over the Standard Line models.

AGENCY ARMS MID LINE GLOCK 34 BARREL

$180.00
Agency Arms Mid Line are for those who desire functionality as well as a unique appearance. While each of our lines maintain the same core accuracy and reliability, Our Mid Line focuses on additional machining enhancements and appearance while only a having modest price increase over the Standard Line models.

AGENCY ARMS MID LINE GLOCK 43 BARREL

$180.00
Agency Arms Mid Line are for those who desire functionality as well as a unique appearance. While each of our lines maintain the same core accuracy and reliability, Our Mid Line focuses on additional machining enhancements and appearance while only a having modest price increase over the Standard Line models.

Agency Arms M&P Trigger Kit

$153.00
** AGENCY SHOE IS DESIGNED TO WORK ONLY WITH APEX TACTICAL FORWARD SERE KIT** **DO NOT INSTALL SHOE IN CONJUNCTION WITH OTHER KITS**

AGENCY ARMS STANDARD LINE GLOCK 34 BARREL

$144.00
Agency Arms Standard Line are for those who prefer a purely functional design. While each of our lines maintain the same core accuracy and reliability, the Standard Lines focus are functionality and affordability.

AGENCY ARMS STANDARD LINE GLOCK 17 BARREL

$144.00
Agency Arms Standard Line are for those who prefer a purely functional design. While each of our lines maintain the same core accuracy and reliability, the Standard Lines focus are functionality and affordability.

AGENCY ARMS STANDARD LINE GLOCK 19 BARREL

$144.00
Agency Arms Standard Line are for those who prefer a purely functional design. While each of our lines maintain the same core accuracy and reliability, the Standard Lines focus are functionality and affordability.

AGENCY ARMS STANDARD LINE GLOCK 26 BARREL

$144.00
Agency Arms Standard Line are for those who prefer a purely functional design. While each of our lines maintain the same core accuracy and reliability, the Standard Lines focus are functionality and affordability.

AGENCY ARMS STANDARD LINE GLOCK 43 BARREL

$144.00
Agency Arms Standard Line are for those who prefer a purely functional design. While each of our lines maintain the same core accuracy and reliability, the Standard Lines focus are functionality and affordability.

AGENCY ARMS BONESAW AUTHORIZATION FEE

$150.00 $135.00

Note: This is the ONLY way to order the "Bonesaw" cuts on a CUSTOMER SUPPLIED gun through Agency Arms.

We are accepting Authorization Fee's for Agency Arms to gunsmith a customer supplied Glock pistol finished in the Reactive Gunworks exclusive "Bonesaw" cut.

Customer Supplied Process:
1) Pay the "Bonesaw Authorization Fee" to Reactive Gunworks (each fee entitles you to the design rights for 1 pistol)

2) Using your Order Confirmation code from Reactive Gunworks, place your Bonesaw order directly with Agency Arms and pay the required 50% deposit (at www.AgencyArms.com)

3) Mail your Glock directly to Agency Arms (you will receive shipping instructions directly from Agency)

4) Upon completion of the gunsmithing by Agency Arms, pay the remaining balance due and Agency Arms will return ship your firearm.

How long will it take?
Build Times are provided by Agency Arms and are based off Demand.

Not available on subcompact (ie.G42/43) or long slide (ie.G34/17L) or large

Trijicon HD XR Night Sights GLOCK

$135.00
With the challenges of the changing landscape in law enforcement comes the next evolution of the Trijicon Night Sight line. Building on the features of the current HD™ Night Sights, the Trijicon HD XR™ night sights are for the next level of advanced target identification and engagement at increased distances. A thinner front sight post allows shooters to have a larger field of view which further enhances the ability to identify targets, expedite engagements and see location of hits on target at longer distances. Pistol shooters that need the advantage of a more precise engagement in any light can count on the Trijicon HD XR™ Night Sights.

Trijicon HD Night Sights GLOCK

$121.50
The HD Night Sights were specifically created to address the needs of tactical shooters. The three dot green tritium night sight set’s front sight features a taller blade and an aiming point ringed in photoluminescent paint while the rear sight is outlined in black and features a wider U-shaped notch. This unique configuration increases visibility and quickens front sight acquisition—even in transitional lighting. Additionally, the front surface of the rear sight is steeply hooked to assist in emergency one-handed slide operation. Green tritium lamps are warranted for 12 years from date of manufacture.​

Guncraft Cloak Mod2 Glock 26

$73.80
The Cloak is designed to be worn in either appendix or strong side position, and was built to be comfortable and efficient, making it perfect for everyday carry.

Guncraft Cloak Mod2 Glock 43

$73.80
The Cloak is designed to be worn in either appendix or strong side position, and was built to be comfortable and efficient, making it perfect for everyday carry.

Guncraft Cloak Mod2 Glock 19

$73.80
The Cloak is designed to be worn in either appendix or strong side position, and was built to be comfortable and efficient, making it perfect for everyday carry.

Vickers Elite Battlesight for Glock, Black Serrated

$49.95
The high profile Vickers Elite Battlesight rear has a .145” wide, deep U-Notch for optimum sighting in low-light, dynamic range conditions and is a perfect match to our .125” wide front sights. The concave non-reflective rear blade is serrated 40 lines per inch, while the notch area is recessed into a semi-circular pocket for a crisp, protected sight picture. Two hardened set-screws ensure this sight will never shoot loose under the most demanding conditions. This snag-free rear sight also has a shelf shape that enables one-hand slide cycling or malfunction clearance and a rugged, non-reflective matte black parkerized finish. The Vickers Elite Battlesight is available with single dot Tritium and plain black serrated rear blades and your choice of black serrated, green/red fiber optic, tritium and genuine, never dulling gold bead front sight styles. The high profile of the Vickers Elite Battlesight allows the use of a taller front sight and deeper rear notch for better sight tracking during high speed shooting situations. Once you try this sight system you will be convinced that the Vickers Elite Battlesight is the best performance upgrade you can make to your Glock® pistol! Larry Vickers is a retired US Army 1st SFOD- Delta combat veteran with years of experience in the firearms industry as a combat marksmanship instructor and industry consultant. Find out more about Larry Vickers on his website www.vickerstactical.com NOTE: Sights may require minor fitting and may not be returned after installation. The Vickers Elite Glock® Sight set requires the use of a .245”tall front sight for all caliber Glock® pistols except for .45 ACP and 10mm which will typically require the .230” front sight. Sights may require minor fitting and may not be returned after installation. These front sights are taller than factory Glock® and not compatible with standard factory rear sights without adjusting the sight height. Wilson Combat Vickers Glock® rear sights are not compatible with factory Glock® MOS (Modular Optic System) slide models due to the rearward relocation of the sight dovetail position. Glock Rear Sight Installation FAQ Remove the magazine and make sure your pistol is unloaded. Remove and Field strip slide assembly and secure the slide in a padded vise. Remove existing rear sight with hammer and punch. Clean rear sight dovetail and press in new rear sight from right to left. If rear sight will not start into approximately 50% of the dovetail you may need to remove very small amounts of material from the bottom and sides of the dovetail portion of the rear sight-usually just a few light passes will do. A safe sided dovetail file, small diamond hone or sanding stick are good tools for this. Go slowly and check your fit. Once you are able to get 50% of the sight base into the dovetail attempt to tap the sight in place with a hammer and non marring punch/dowel (wood, polymer, aluminum) or appropriate sight pusher. If using a steel or brass punch protect the sight/punch with several layers of duct tape. Fine adjust your windage with a rear sight armorers tool or non marring punch. After you fine adjust rear sight windage install dual locking screws with a threadlocking compound like Loctite on the threads. Note-if the rear sight is loose in the dovetail your dovetail is cut oversize and the new rear sight may require peening on the edges of the dovetail for a proper fit.

Agency Arms Battle Plates

$40.50
Bonesaw Battleplate

Vickers Elite Snag Free Front Sight for Glock, Green Fiber Optic, .230"

$39.95
Snag Free Front Sight, Green Fiber Optic, Vickers Elite for Glock® .230” .230” height .125" wide Green Fiber optic (.0585" Diameter) Glock® Vickers Elite replacement front sight for .45 ACP and 10mm calibers Black Parkerized finish Note: .The Vickers Elite Glock® Sight set requires the use of a .245” tall front sight for all caliber Glock® pistols except for .45 ACP and 10mm which will typically require the .230” front sight. Sights may require minor fitting and may not be returned after installation. These front sights are taller than factory Glock® and not compatible with standard factory rear sights without adjusting the sight height. Replacement fiber optic rods found here: http://shopwilsoncombat.com/Fiber-Optic-Rod-Replacement-Green-0585-x-1/productinfo/583G/ Glock Front Sight Installation FAQ Remove the magazine and make sure your pistol is unloaded. Remove and field strip slide assembly. Remove Glock factory front sight with a punch or pliers. Gen-4 Glock pistols will require a front sight tool to remove the front sight retaining screw. After removal of front sight clean and degrease sight hole in slide and check the fit of the new front sight. If the new sight will seat at least 50% tap it in place with a non marring punch taking care that it remains straight. If the sight will not seat you may have to sand or lightly file the circumference of the front sight base. Install with aftermarket Glock front sight tool or 3/16” socket that has been modified to clear the slide. For a more permanent installation use red loctite around the circumference of the sight base. Reassemble your pistol and make sure sight retaining screw is not impeding operation.

Guncraft Rapid Mag Carrier Core

$29.70
Our new mag carrier for Glock 9mm/40cal magazines. This mag carrier is fully ambidextrous and IWB/OWB compatible. The user can wear the mag carrier inside waistband or outside waistband without having to change mounting hardware etc. This versatile mag carrier is a perfect item to add to your EDC or training setup.

Agency Arms Pistol Case

$22.50
Lockable case that fits inside of the Glock OEM Case.

RG HATS

$18.00
Get your Swag on and wear these Hats proud! Mesh Back Adjustable Snap!

Men's RPG T-Shirt BLACK

$16.20
Get your Swag on and wear these shirts proud!

Men's Auto Out Black T-Shirt

$16.20
Get your Swag on and wear these shirts proud!

Men's Auto Out Grey T-Shirt

$16.20
Get your Swag on and wear these shirts proud!

Men's Saw T-shirt Charcoal

$16.20
Get your Swag on and wear these shirts proud!

Men's #MERICA T-Shirt Charcoal

$16.20
Get your Swag on and wear these shirts proud!

Men's #MERICA T-Shirt Red

$16.20
Get your Swag on and wear these shirts proud!

Men's FLAG T-Shirt Charcoal

$16.20
Get your Swag on and wear these shirts proud!

Men's RG SHIELD T-Shirt BLACK

$16.20
Get your Swag on and wear these shirts proud!

Men's RG ROUND T-Shirt BLACK

$16.20
Get your Swag on and wear these shirts proud!

Men's RG ROUND T-Shirt GREY

$16.20
Get your Swag on and wear these shirts proud!

Men's RG ROUND T-Shirt BLUE

$16.20
Get your Swag on and wear these shirts proud!

Women's RG V-Neck BLACK

$12.60
Get your Swag on and wear these shirts proud!

Women's RG V-Neck WHITE

$12.60
Get your Swag on and wear these shirts proud!

Women's RG V-Neck GREY

$12.60
Get your Swag on and wear these shirts proud!

Women's RG Tank ORANGE

$12.60
Get your Swag on and wear these shirts proud!

Reactive PVC Patches

$4.46
High Quality PVC Patches. 3" x 3" "RG" Shield 3" x 1" "Reactive Gunworks" Blackout 3" x 1.5" "RG" Whiteout Flag